Video

Published August 16, 2020 © GPL3+

"UVC Box" a DIY UV Sterilizer

A low cost easy to re-make UVC Sterilizer for sterilizing medical equipment and stuff.

BeginnerFull instructions provided4 hours11,105

Things used in this project

Hardware components

Microchip attiny84

uvc leds

Arduino Nano R3

for programming Attiny84

UTSOURCE Electronic Parts

Software apps and online services

Arduino IDE

Hand tools and fabrication machines

3D Printer (generic)

ferric chloride

Story

Video-

So this is "UVC BOX" a low cost easy to make UVC Sterilizer which is made for sterilizing things like Medical equipment, daily use things like smartphones, wallets, coins bills, etc.

1 / 2

its low costing because I've used some generic low costing parts like this plastic container or jewelry box which you can buy for very cheap, I designed the housing in Fusion360 and then 3D printed it. it fits onto the lid of the container perfectly.

The hardest part was getting the UVC LEDs, I found some on Utsource's website.

you can check UTSOURCE.net, they deal in all kinds of electronics components like for example Attiny84 and other electronic components that I'm using in this project.

after getting the UVC LEDs I solder them on some MCPCBs I made in past, basically, I connected them in parallel and provide them 3.3V for powering them.

1 / 2

After testing the LEDs, I made a setup which consists of total 6 Outputs and 1 Input, (5 for indication LEDs and 1 for UVC LED, 1 Input for button) and upload the code to my Attiny84 Breakout board Via Arduino as ISP setup

check out about this more from here- https://www.hackster.io/350166/getting-started-with-attiny84-c920ee

Code basically turns the indicator LED on in a chaser sequence (from 1 to 5) and then we can press the button for Toggling the UVC Led, UVC Led will stay ON for around 10 minutes and then turn OFF.

1 / 3

After testing this on a breadboard I designed and then etched a Custom PCB for this Project and assemble everything on it (watch the video for Assembly and basic Test result)

After that, I Hooked it up with my custom Arduino as ISP Programmer which I made a few weeks ago for Programing/Flashing MCUs; more about that here-https://www.hackster.io/Oniichan_is_ded/multiple-attiny85-13a-programmer-84adf8

I uploaded the UVC BOX sketch to the custom etched circuit and Tested it one last time by connecting Rocker Switch and Push-button with Lithium Cell with it.

after that, I glued the circuit inside the 3D printed Casing and Assemble everything together.

1 / 2

And that's it, In the V2 I will make a better encloser because this jewelry box container is not very durable (it will probably break in a few months of daily use)

Also, this setup is basically identical in working with the commercially available UVC sterilizer, the only difference is the price(this is cheaper)

For a better Tutorial of this project, watch the video-

I've Attached everything related to this project, leave a comment if you guys run into any problem.

Schematics

Code

CODE

const int buttonPin = 0;    //7 arduino pin
const int UVPin =  5;     //13 arduino pin

int pinsCount=5;                        
int pins[] = {10,9,8,7,6};   //2,3,4,5,6 arduino pin

int buttonState = 0;        

void setup() {
  pinMode(UVPin, OUTPUT);
  pinMode(buttonPin, INPUT_PULLUP);

  for (int i=0; i<pinsCount; i=i+1){    
   pinMode(pins[i], OUTPUT); 
  }

  for (int i=0; i<pinsCount; i=i+1){    
    digitalWrite(pins[i], HIGH);         
    delay(1000);                          
    digitalWrite(pins[i], LOW);          
  }
}

void loop() {
  buttonState = digitalRead(buttonPin);
if (buttonState == LOW) {
    digitalWrite(UVPin, HIGH);
    delay(600000);
    digitalWrite(UVPin, LOW);
  } else {
  }
}

Credits

Arnov Sharma

310 projects • 311 followers

Just your average MAKER

"UVC Box" a DIY UV Sterilizer

Things used in this project

Hardware components

Software apps and online services

Hand tools and fabrication machines

Story

Video-

Custom parts and enclosures

Encloser STL FILE

Schematics

PCB for etching

SCH

Code

CODE

Credits

Arnov Sharma

Comments

Embed the widget on your own site

"UVC Box" a DIY UV Sterilizer

"UVC Box" a DIY UV Sterilizer

Things used in this project

Hardware components

Software apps and online services

Hand tools and fabrication machines

Story

Video-

Custom parts and enclosures

Encloser STL FILE

Schematics

PCB for etching

SCH

Code

CODE

Credits

Arnov Sharma

Comments

Related channels and tags