Published July 11, 2017 © MIT

Gyroscope With Arduino 101

Learn how to read Gyroscope Sensor on Arduino 101 and show tilt status on LED.

BeginnerProtip1 hour9,589

Things used in this project

Hardware components

Arduino 101

LED (generic)

Resistor 221 ohm

Jumper wires (generic)

Software apps and online services

Arduino IDE

Story

Learn how to read Gyroscope Sensor on Arduino 101 and show tilt status on LED.

Arduino 101 is good for IOT starters. Having the Intel® Curie™ Module, designed to integrate the core's low power-consumption and high performance with the Arduino's ease-of-use, Bluetooth Low Energy capabilities and on-board 6-axis accelerometer/gyroscope, this board will provide exciting opportunities for building creative projects in the connected world.

More information about the technical specifications and documentation can be found on the Arduino/Genuino 101 main page.

Build Circuit

1 / 3

Lets build our circuit!

Connect Arduino 101 pin GND (ground) to one of the bread board pins. I picked the upper left pin.

Connect 3 resistor on the same column of the GND jumper wire

Add 3 LEDs each negative pin is connected to the other end of its resistor

Grab 3 jumper wire

Connect 1st LED's positive pin to Digita Pin ~9

Connect 2nd LED's positive pin to Digita Pin ~6

Connect 3d LED's positive pin to Digita Pin ~5

Our circuit must be look like the images above.

Program the Arduino 101

Plug in your Arduino 101.

1 / 4

Download GyroscopeSensor.ino source code and upload it.

Arduino 101 has Intel Curie Module that uses Arduino api CurieIMU.h We can read the accelerometer and gyroscope using this function.

CurieIMU.readMotionSensor(ax, ay, az, gx, gy, gz);

The axis variables are used as parameter and will be referenced by the api to update the values.

Finally get the brightness of led using the formula and update the LED

if(gx>0)
    gxBrightness = gx/66.66;   
else
     gxBrightness=0;
analogWrite(gxLed,gxBrightness);   // show gyroscope's X Axis brightness
if(gy>0)
     gyBrightness = gy/66.66;
else
     gyBrightness=0;   
analogWrite(gyLed,gyBrightness); // show gyroscope's Y Axis brightness
if(gz>0)
     gzBrightness = gz/66.66;   
else
     gzBrightness=0;   
analogWrite(gzLed,gzBrightness); // show gyroscope's Z Axis brightness

Code

GyroscopeSensor

#include "CurieIMU.h"
int ax, ay, az;         // accelerometer values
int gx, gy, gz;         // gyrometer values

int gxBrightness = 0;
int gxLed = 9;

int gyBrightness = 0;
int gyLed = 6;


int gzBrightness = 0;
int gzLed = 5;

void setup(){
  
  pinMode(gxLed, OUTPUT); 
  pinMode(gyLed, OUTPUT); 
  pinMode(gzLed, OUTPUT); 
  Serial.begin(9600); // initialize Serial communication
  CurieIMU.begin();
  delay(5000); // Allow the user to set everything down
  CurieIMU.autoCalibrateGyroOffset();
  CurieIMU.autoCalibrateAccelerometerOffset(X_AXIS, 0);
  CurieIMU.autoCalibrateAccelerometerOffset(Y_AXIS, 0);
  CurieIMU.autoCalibrateAccelerometerOffset(Z_AXIS, 0);
}

String jsonEncodeValue(String key, float keyVal){
  return "\"" + key + "\":" + String(keyVal) + "";
}

String assembleJson(String keysAndVals){
  return "{" + keysAndVals + "}";
}

void loop(){
  // read raw accel/gyro measurements from device
  CurieIMU.readMotionSensor(ax, ay, az, gx, gy, gz);

  // display JSON formatted accel/gyro x/y/z values
  String keyVals = jsonEncodeValue("ax", ax) + ",";
  keyVals += jsonEncodeValue("ay", ay) + ",";
  keyVals += jsonEncodeValue("az", az) + ",";
  keyVals += jsonEncodeValue("gx", gx) + ",";
  keyVals += jsonEncodeValue("gy", gy) + ",";
  keyVals += jsonEncodeValue("gz", gz);
  
  if(Serial){
    Serial.println(keyVals);
  }
  delay(100);

  if(gx>0)
    gxBrightness = gx/66.66;
  else
    gxBrightness=0;
  analogWrite(gxLed,gxBrightness);

  if(gy>0)
    gyBrightness = gy/66.66;
  else
    gyBrightness=0;
  analogWrite(gyLed,gyBrightness);
  

  
  if(gz>0)
    gzBrightness = gz/66.66;
  else
    gzBrightness=0;
  analogWrite(gzLed,gzBrightness);

}

Credits

Jeff-Paredes

1 project • 126 followers

Programming is my love and engineering is my third party :)

Gyroscope With Arduino 101

Things used in this project

Hardware components

Software apps and online services

Story

Build Circuit

Program the Arduino 101

Schematics

Schematics

Code

GyroscopeSensor

Credits

Jeff-Paredes

Comments

Embed the widget on your own site

Gyroscope With Arduino 101

Gyroscope With Arduino 101

Things used in this project

Hardware components

Software apps and online services

Story

Build Circuit

Program the Arduino 101

Schematics

Schematics

Code

GyroscopeSensor

Credits

Jeff-Paredes

Comments

Related channels and tags