Heart Attack Preventer

Laith Adnan, [24.07.19 17:41]
[ Photo ]

Laith Adnan, [24.07.19 20:07]
#include <LiquidCrystal.h>
#define IN1  8
#define IN2  9
#define IN3  10
#define IN4  7                                        
int Steps = 4096; //4096 or 768
int cstep = 0;
const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2;
const int buzzer = 9;
LiquidCrystal lcd(12, 11, 5, 4, 3, 2);

int pulsePin = A0;                 // Pulse Sensor purple wire connected to analog pin A0
int blinkPin = 13;                // pin to blink led at each beat
// Volatile Variables, used in the interrupt service routine!
volatile int BPM;                   // int that holds raw Analog in 0. updated every 2mS
volatile int Signal;                // holds the incoming raw data
volatile int IBI = 600;             // int that holds the time interval between beats! Must be seeded! 
volatile boolean Pulse = false;     // "True" when User's live heartbeat is detected. "False" when not a "live beat". 
volatile boolean QS = false;        // becomes true when Arduoino finds a beat.

static boolean serialVisual = true;   // Set to 'false' by Default.  Re-set to 'true' to see Arduino Serial Monitor ASCII Visual Pulse 

volatile int rate[10];                      // array to hold last ten IBI values
volatile unsigned long sampleCounter = 0;          // used to determine pulse timing
volatile unsigned long lastBeatTime = 0;           // used to find IBI
volatile int P = 512;                      // used to find peak in pulse wave, seeded
volatile int T = 512;                     // used to find trough in pulse wave, seeded
volatile int thresh = 525;                // used to find instant moment of heart beat, seeded
volatile int amp = 100;                   // used to hold amplitude of pulse waveform, seeded
volatile boolean firstBeat = true;        // used to seed rate array so we startup with reasonable BPM
volatile boolean secondBeat = false;      // used to seed rate array so we startup with reasonable BPM

void setup()
{
   pinMode(IN1, OUTPUT); 
  pinMode(IN2, OUTPUT); 
  pinMode(IN3, OUTPUT); 
  pinMode(IN4, OUTPUT); 
   pinMode(buzzer,OUTPUT);
  pinMode(blinkPin,OUTPUT);         // pin that will blink to your heartbeat!
  Serial.begin(115200);             // we agree to talk fast!
  interruptSetup();                 // sets up to read Pulse Sensor signal every 2mS 
                                    // IF YOU ARE POWERING The Pulse Sensor AT VOLTAGE LESS THAN THE BOARD VOLTAGE, 
                                    // UN-COMMENT THE NEXT LINE AND APPLY THAT VOLTAGE TO THE A-REF PIN
                                    //   analogReference(EXTERNAL);   
 lcd.begin(16, 2);
 lcd.clear();
}


//  Where the Magic Happens
void loop()
{
   serialOutput();  
    lcd.print("DEVICE-STATE");
     lcd.setCursor(1,1);
     lcd.print("UPDATING... ");
     lcd.setCursor(5,1);
     delay(3000);
     lcd.clear();
  if (QS == true) // A Heartbeat Was Found
    {     
      // BPM and IBI have been Determined
      // Quantified Self "QS" true when arduino finds a heartbeat
      serialOutputWhenBeatHappens(); // A Beat Happened, Output that to serial.     
      QS = false; // reset the Quantified Self flag for next time  
      state(); 
      buzer();
      inject(); 
    }
     
  delay(20); //  take a break
}


void interruptSetup()
{     
  // Initializes Timer2 to throw an interrupt every 2mS.
  TCCR2A = 0x02;     // DISABLE PWM ON DIGITAL PINS 3 AND 11, AND GO INTO CTC MODE
  TCCR2B = 0x06;     // DON'T FORCE COMPARE, 256 PRESCALER 
  OCR2A = 0X7C;      // SET THE TOP OF THE COUNT TO 124 FOR 500Hz SAMPLE RATE
  TIMSK2 = 0x02;     // ENABLE INTERRUPT ON MATCH BETWEEN TIMER2 AND OCR2A
  sei();             // MAKE SURE GLOBAL INTERRUPTS ARE ENABLED      
} 

void serialOutput()
{   // Decide How To Output Serial. 
 if (serialVisual == true)
  {  
     arduinoSerialMonitorVisual('-', Signal);   // goes to function that makes Serial Monitor Visualizer
  } 
 else
  {
      sendDataToSerial('S', Signal);     // goes to sendDataToSerial function
   }        
}

Laith Adnan, [24.07.19 20:07]
void serialOutputWhenBeatHappens()
{    
 if (serialVisual == true) //  Code to Make the Serial Monitor Visualizer Work
   {            
     Serial.print(" Heart-Beat Found ");  //ASCII Art Madness
     Serial.print("BPM: ");
     Serial.println(BPM);
     lcd.print("Heart-Beat Found ");
     lcd.setCursor(1,1);
     lcd.print("BPM: ");
     lcd.setCursor(5,1);
     lcd.print(BPM);
     delay(3000);
     lcd.clear();
   }
 else
   {
     sendDataToSerial('B',BPM);   // send heart rate with a 'B' prefix
     sendDataToSerial('Q',IBI);   // send time between beats with a 'Q' prefix
   }   
}

void arduinoSerialMonitorVisual(char symbol, int data )
{    
  const int sensorMin = 0;      // sensor minimum, discovered through experiment
  const int sensorMax = 1024;    // sensor maximum, discovered through experiment
  int sensorReading = data; // map the sensor range to a range of 12 options:
  int range = map(sensorReading, sensorMin, sensorMax, 0, 11);
  // do something different depending on the 
  // range value:
}


void sendDataToSerial(char symbol, int data )
{
   Serial.print(symbol);
   Serial.println(data);                
}

ISR(TIMER2_COMPA_vect) //triggered when Timer2 counts to 124
{  
  cli();                                      // disable interrupts while we do this
  Signal = analogRead(pulsePin);              // read the Pulse Sensor 
  sampleCounter += 2;                         // keep track of the time in mS with this variable
  int N = sampleCounter - lastBeatTime;       // monitor the time since the last beat to avoid noise
                                              //  find the peak and trough of the pulse wave
  if(Signal < thresh && N > (IBI/5)*3) // avoid dichrotic noise by waiting 3/5 of last IBI
    {      
      if (Signal < T) // T is the trough
      {                        
        T = Signal; // keep track of lowest point in pulse wave 
      }
    }

  if(Signal > thresh && Signal > P)
    {          // thresh condition helps avoid noise
      P = Signal;                             // P is the peak
    }                                        // keep track of highest point in pulse wave

  //  NOW IT'S TIME TO LOOK FOR THE HEART BEAT
  // signal surges up in value every time there is a pulse
  if (N > 250)
  {                                   // avoid high frequency noise
    if ( (Signal > thresh) && (Pulse == false) && (N > (IBI/5)*3) )
      {        
        Pulse = true;                               // set the Pulse flag when we think there is a pulse
        digitalWrite(blinkPin,HIGH);                // turn on pin 13 LED
        IBI = sampleCounter - lastBeatTime;         // measure time between beats in mS
        lastBeatTime = sampleCounter;               // keep track of time for next pulse
  
        if(secondBeat)
        {                        // if this is the second beat, if secondBeat == TRUE
          secondBeat = false;                  // clear secondBeat flag
          for(int i=0; i<=9; i++) // seed the running total to get a realisitic BPM at startup
          {             
            rate[i] = IBI;                      
          }
        }
  
        if(firstBeat) // if it's the first time we found a beat, if firstBeat == TRUE
        {                         
          firstBeat = false;                   // clear firstBeat flag
          secondBeat = true;                   // set the second beat flag
          sei();                               // enable interrupts again
          return;                              // IBI value is unreliable so discard it
        }   
      // keep a running total of the last 10 IBI values
      word runningTotal = 0;                  // clear the runningTotal variable    

      for(int i=0; i<=8; i++)
        {                // shift data in the rate array
          rate[i] = rate[i+1];                  // and drop the oldest IBI value 
          runningTotal += rate[i];              // add up the 9 oldest IBI values
        }

Laith Adnan, [24.07.19 20:07]
rate[9] = IBI;                          // add the latest IBI to the rate array
      runningTotal += rate[9];                // add the latest IBI to runningTotal
      runningTotal /= 10;                     // average the last 10 IBI values 
      BPM = 60000/runningTotal;               // how many beats can fit into a minute? that's BPM!
      QS = true;                              // set Quantified Self flag 
      // QS FLAG IS NOT CLEARED INSIDE THIS ISR
    }                       
  }

  if (Signal < thresh && Pulse == true)
    {   // when the values are going down, the beat is over
      digitalWrite(blinkPin,LOW);            // turn off pin 13 LED
      Pulse = false;                         // reset the Pulse flag so we can do it again
      amp = P - T;                           // get amplitude of the pulse wave
      thresh = amp/2 + T;                    // set thresh at 50% of the amplitude
      P = thresh;                            // reset these for next time
      T = thresh;
    }

  if (N > 2500)
    {                           // if 2.5 seconds go by without a beat
      thresh = 512;                          // set thresh default
      P = 512;                               // set P default
      T = 512;                               // set T default
      lastBeatTime = sampleCounter;          // bring the lastBeatTime up to date        
      firstBeat = true;                      // set these to avoid noise
      secondBeat = false;                    // when we get the heartbeat back
    }

  sei();                                   // enable interrupts when youre done!
}// end isr
void buzer(){
  // dangerous situation or pressed button
  if (BPM < 60 )
   {
     lcd.print("hypotension");
     lcd.setCursor(1,1);
     lcd.print("BPM: ");
     lcd.setCursor(5,1);
     lcd.print(BPM);
     delay(3000);
     lcd.clear();
   digitalWrite(buzzer,HIGH);
    delay(500);             
   digitalWrite(buzzer,LOW); 
    delay(500);  

}
    
}
void inject()
{
   if (BPM>160)
   {
     lcd.print("Hypertention");
     lcd.setCursor(1,1);
     lcd.print("BPM: ");
     lcd.setCursor(5,1);
     lcd.print(BPM);
     delay(5000);
     lcd.clear();
  for(int x=0;x<Steps;x++)
  {
   switch(cstep)
  {
   case 0:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, HIGH);
   break; 
   case 1:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, HIGH);
     digitalWrite(IN4, HIGH);
   break; 
   case 2:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, HIGH);
     digitalWrite(IN4, LOW);
   break; 
   case 3:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, HIGH);
     digitalWrite(IN3, HIGH);
     digitalWrite(IN4, LOW);
   break; 
   case 4:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, HIGH);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, LOW);
   break; 
   case 5:
     digitalWrite(IN1, HIGH); 
     digitalWrite(IN2, HIGH);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, LOW);
   break; 
     case 6:
     digitalWrite(IN1, HIGH); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, LOW);
   break; 
   case 7:
     digitalWrite(IN1, HIGH); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, HIGH);
   break; 
   default:
     digitalWrite(IN1, LOW); 
     digitalWrite(IN2, LOW);
     digitalWrite(IN3, LOW);
     digitalWrite(IN4, LOW);
   break; 
  }
   
   cstep=cstep+1;
   if(cstep==8)
     {cstep=0;}

  delayMicroseconds(2500);
 
   }
}
}
void state()
{
  if (BPM > 60 & BPM < 74){
   lcd.print("VERY-GOOD");
     lcd.setCursor(1,1);
     lcd.print("BPM: ");
     lcd.setCursor(5,1);
     lcd.print(BPM);
     delay(3000);
     lcd.clear();
  }
}