Tibbo > Hardware > Tibbo Project System > Tibbit Blocks

^® Blocks

Tibbits^® (as in "Tibbo Bits") are blocks of prepackaged I/O functionality housed in brightly colored rectangular shells. It is the Tibbit blocks that give our Tibbo Project System (TPS) its flexibility. This page lists all available Tibbits. To learn more about Tibbo classification and general properties click here.

Not directly related to Tibbits, but very useful in combination with TPS devices are RS485 Modbus sensors and Cable probes. Do remember to check out our sensor offerings as well!

Show All

E.g., input, 5V, relay, RS232, #00_1

#001

#001Four direct I/O lines

M1S

USD4.18

Four directly exposed I/O lines of the microcontroller.

#002

#002Three direct I/O lines and ground

M1S

USD4.18

Three directly exposed I/O lines of the microcontroller plus the ground line.

#003

#003Two direct I/O lines, +5V power, ground

M1S

USD4.18

Two directly exposed I/O lines of the microcontroller plus the +5V output and ground lines.

#01

#01Four-line RS232 port

M1S

USD12.53

Simple RS232 port with only TX, RX, RTS, and CTS lines.

#02

#02RS232/422/485 port

M2S

USD32.01

Universal RS232/422/485 port with electronic mode selection.

#031

#031Two low-power relays (configuration 1)

M1S

USD18.10

Two mechanical low-power relays with independent normally opened terminals.

#032

#032Two low-power relays (configuration 2)

M1S

USD18.10

Two mechanical low-power relays with joined middle (common) terminals. Relay 1 has normally closed and normally opened terminals. Relay 2 only has the normally opened terminal exposed.

#041

#041Two isolated inputs

M1S

USD11.13

Two optically isolated inputs with independent terminals. Inputs are fully isolated from system ground.

#042

#042Three isolated inputs, common (-)

M1S

USD11.13

Three optically isolated inputs with common (-). Inputs are fully isolated from system ground.

#043

#043Three isolated inputs, common (+)

M1S

USD11.13

Three optically isolated inputs with common (+). Inputs are fully isolated from system ground.

#044

#044Four opto-inputs, common ground

M1S

USD11.13

Four opto-couple inputs with the '-' terminal connected to the system ground, independent '+' terminals.

#045

#045Two 24V isolated inputs

M1S

USD11.13

Two optically isolated inputs with independent terminals. Inputs are fully isolated from system ground.

#046

#046Three 24V isolated inputs, common (-)

M1S

USD11.13

Three optically isolated inputs with common (-). Inputs are fully isolated from system ground.

#047

#047Three 24V isolated inputs, common (+)

M1S

USD11.13

Three optically isolated inputs with common (+). Inputs are fully isolated from system ground.

#048

#048Four 24V isolated inputs, common ground

M1S

USD11.13

Four opto-couple inputs with the '-' terminal connected to the system ground, independent '+' terminals.

#05

#05RS485 port

M1S

USD6.96

RS485 port with full-duplex or half-duplex operation.

#06

#06Two high-power relays

M2T

USD19.48

Two mechanical high-power relays with normally opened and normally closed terminals.

#07

#07Two solid state relays

M1S

USD32.01

Two solid state normally opened relays.

#08

#08Wiegand and clock/data reader port

M1S

USD13.92

Wiegand and clock/data reader port plus one open collector output.

#09

#09Low-power 5V supply, 12V input

M1S

USD9.75

Low-power non-isolated power supply with 5V output, 9-18V input range, shutdown control.

#10

#10Medium-power 5V supply, 12V input

M1T

USD20.88

Medium-power non-isolated power supply with 5V output, 9-18V input range, and shutdown control.

#11

#11Four open collector outputs

M1S

USD12.53

Four open collector outputs.

#12

#12Low-power +15/-15V power supply, 5V input

M1S

USD44.53

Low-power non-isolated power supply with +15/-15V output, 5V input, shutdown control.

#13

#13Four-channel ADC

M1S

USD43.14

Four-channel ADC with -10V ~ +10V range.

#14

#14Four-channel DAC

M1S

USD25.05

Four-channel DAC with -10V ~ +10V range.

#15

#15High-voltage AC solid state relay

USD19.48

High-voltage AC solid state normally opened relay.

#16

#16Three PWMs with open collector outputs

M1S

USD19.48

Three PWMs with open collector outputs.

#17

#17Three PWMs with power outputs

M1S

USD20.88

Three PWMs with power outputs (the power must be supplied externally).

#18

#18Power input

USD4.18

Power jack and two terminal blocks.

#19

#19DB9M connector

USD4.18

DB9M connector.

#20

#20Nine terminal blocks

USD9.75

Nine terminal blocks.

#21

#21Four terminal blocks

USD5.57

Four terminal blocks.

#22

#22RTD Temperature Meter

M1S

USD33.40

RTD temperature meter.

#23

#23Isolated PoE power supply, 5V output

M2T

USD59.90

Isolated PoE power supply with 5V output, shutdown control. Also can be used as generic isolated power supply with 35-60V input range.

#25

#25High-power 5V supply, 12/24/48V input

M2T

USD45.93

High-power non-isolated power supply with 5V output, 8-60V input range, and shutdown control.

#26

#26IR code processor

M1S

USD44.53

Records and plays back infrared commands (codes) of conventional IR remote controls.

#27

#27IR Receiver/Transmitter

USD19.48

Infrared receiver circuitry and transmitter diode.

#28

#28Ambient light sensor

USD20.88

Visible spectrum ambient light sensor.

#29

#29Ambient temperature meter

USD9.75

Ambient temperature meter.

#30

#30Temperature/humidity meter

USD40.36

Temperature/humidity meter.

#31

#31PIC coprocessor

M1S

USD18.10

ADC, PWM, I/O based on PIC 16F1824 microprocessor.

#33

#33Wide input range power supply

M1T

USD69.21

8-60V input voltage (12V/24V/48V) 1.5A output current with spikes up to 2A

#35

#35Barometric pressure sensor

USD25.05

Barometric pressure sensor.

#36

#363-axis accelerometer

USD40.36

3-axis accelerometer (shock sensor).

#37

#37RF connector

USD16.70

RF connector.

#38

#38Pushbutton

USD4.18

One pushbutton.

#391

#391Large green LED (low brightness)

USD8.35

Large green LED (low brightness)

#392

#392Large red LED (high brightness)

USD8.35

Large red LED (high brightness)

#393

#393Large yellow LED (low brightness)

USD8.35

Large yellow LED (low brightness)

#394

#394Large blue LED (high brightness)

USD8.35

Large blue LED (high brightness)

#401

#401Digital potentiometer, 5KOhm

M1S

USD12.53

Digital potentiometer, 5KOhm, 8-bit resolution.

#402

#402Digital potentiometer, 10KOhm

M1S

USD12.53

Digital potentiometer, 10KOhm, 8-bit resolution.

#403

#403Digital potentiometer, 50KOhm

M1S

USD12.53

Digital potentiometer, 50KOhm, 8-bit resolution.

#404

#404Digital potentiometer, 100KOhm

M1S

USD12.53

Digital potentiometer, 100KOhm, 8-bit resolution.

#41

#418-bit port (supplied with 200mm cable)

USD22.26

8-bit port (supplied with 200mm cable).

#42

#42RTC and NVRAM with backup

M1S

USD32.01

Real-time clock and non-volatile memory with backup battery and interrupt output.

#431

#4314-Channel Streaming ADC ±10V

M1S

USD59.90

12-bit, precise, 4-Channel Streaming ADC ±10V (Single-ended) and 20V (Differential).

#432

#4324-Channel Streaming ADC ±100V

M1S

USD69.21

12-bit, precise, 4-Channel Streaming ADC ±100V (Single-ended) and 200V (Differential).

#441

#441Isolated RS232/422/485 port

USD54.57

Isolated RS232/422/485 port with DB9M connector.

#442

#442Isolated RS232/422/485 port

USD54.57

Isolated RS232/422/485 port with terminal block.

#451

#451LTE (4G) Modem (SA)

USD118.46

This version of Tibbit #45 supports LTE bands B1, B3, B5, B7, B8, and B28.

#452

#452LTE (4G) Modem (E)

USD118.46

This version of Tibbit #45 supports LTE bands B1, B3, B7, B8, and B20.

#453

#453LTE (4G) Modem (A)

USD118.46

This version of Tibbit #45 supports LTE bands B2, B4, and B12.

#46

#46Cat-M1/NB-IoT Modem

USD98.49

Supports LTE-M1(CAT-M1) and LTE-NB1 (NB-IoT)

#50

#50Mini type B USB port

C1This Tibbit is not available for purchase.

Mini-B USB port with OTG

#52

#52Four-channel isolated +/-10V ADC

M2TThis Tibbit is not available for purchase.

Four-channel isolated ADC with -10V ~ +10V range.

#53

#53Isolated 4-20mA ADC

M2T

USD74.54

Two-channel isolated ADC with 4 ~ 20mA range. Not recommended for new designs.

#54

#54Four dry contact inputs

M1S

USD12.53

Four dry contact inputs; external switches should be installed between the input terminals and the system ground.

#57

#57FPGA Tibbit

M1S

USD44.53

Contains an ICE5LP1K-SWG36ITR50 FPGA from Lattice Semiconductor

#58

#58Two 24V NPN isolated open collector outputs

M1S

USD25.05

Two 24V NPN isolated open collector outputs

#59

#59Two 24V PNP isolated open collector outputs

M1S

USD25.05

Two 24V PNP isolated open collector outputs

#611

#611Isolated ±10V, 4-20mA ADC with 24V Output

USD95.00

Isolated two-channel ±10V and two-channel 4-20mA ADC with 24V output

#612

#612Isolated ±10V, 4-20mA ADC

USD78.00

Isolated two-channel ±10V and two-channel 4-20mA ADC

#62

#62One-wire Tibbit

M1T

USD31.90

ONe-wire/Single-wire Tibbit

#631

#631AC Voltage Detector (110V)

USD32.01

AC Voltage Detector 110V (also referred to as 120V AC)

#632

#632AC Voltage Detector (220V)

USD32.01

AC Voltage Detector 220V (also referred to as 230V or 240V AC)

#WA2000C

#WA2000CWA2000C Wi-Fi Add-on Module

WIFI

USD

WA2000C Wi-Fi Add-on Module

#WA2000U

#WA2000UWA2000U Wi-Fi Add-on Module

WIFI

USD

WA2000U Wi-Fi Add-on Module

#WM6256

#WM6256WM6256 Wi-Fi Add-on Module

WIFI

USD

WM6256 Wi-Fi Add-on Module

Programmable IoT

Serial-over-IP (SoI)

Modbus Gateways

Remote IO

Linux Ecosystem

IO Ninja

Modules and Boards

Add-on Boards

Chip-level products

Serial Controllers

Tibbo Project System

Sensors

WebUSB Boards

IO Ninja Hardware

Add-ons and Accessories

Modules and Boards

Add-on Boards

Chip-level products

Serial Controllers

Tibbo Project System

Sensors

WebUSB Boards

IO Ninja Hardware

Add-ons and Accessories

Programmable IoT

Serial-over-IP (SoI)

Modbus Gateways

Remote IO

Linux Ecosystem

IO Ninja

^® Blocks