B-L072Z-LRWAN1

Active

STM32L0 Discovery kit LoRa, Sigfox, low-power wireless

Download databrief Order Direct

Product overview

Description

The B-L072Z-LRWAN1 LoRa®/Sigfox™ Discovery kit is a development tool to learn and develop solutions based on LoRa®, Sigfox™, and FSK/OOK technologies. This Discovery kit features the all-in-one CMWX1ZZABZ-091 open module by Murata. The module is powered by an STM32L072CZ microcontroller and SX1276 transceiver. The transceiver features the LoRa® long-range modem, providing ultra-long-range spread-spectrum communication and high interference immunity, minimizing current consumption. Since CMWX1ZZABZ-091 is an open module, the user has access to all STM32L072CZ peripherals such as ADC, 16-bit timer, LP-UART, I2C, SPI, and USB 2.0 FS (supporting BCD and LPM).

The B-L072Z-LRWAN1 Discovery kit includes an ST-LINK/V2-1 embedded debug tool interface, LEDs, push-buttons, antenna, Arduino™ Uno V3 connectors and USB OTG connector in Micro-B format.

The LoRaWAN™ stack supports Class A, Class B, and Class C. It is available in the I-CUBE-LRWAN firmware package. Several examples, including an AT-command stack, are available to help users set up a complete LoRaWAN™ node.

The Sigfox™ stack is RC1, RC2, RC3c, and RC4 compliant. It is available in the X-CUBE-SFOX Expansion Package. Several examples, including an AT-command modem, are also available to help users set up a complete Sigfox™ node.

  • All features

    • CMWX1ZZABZ-091 LoRa®/Sigfox™ module (Murata)
      • Embedded ultra-low-power STM32L072CZ MCU, based on Arm® Cortex®-M0+ core, with 192 Kbytes of Flash memory, 20 Kbytes of RAM, 20 Kbytes of EEPROM
      • Frequency range: 860 MHz - 930 MHz
      • USB 2.0 FS
      • 4-channel,12-bit ADC, 2 × DAC
      • 6-bit timers, LP-UART, I2C and SPI
      • Embedded SX1276 transceiver
      • LoRa®, FSK, GFSK, MSK, GMSK, and OOK modulations (+ Sigfox™ compatibility)
      • +14 dBm or +20 dBm selectable output power
      • 157 dB maximum link budget
      • Programmable bit rate up to 300 kbit/s
      • High sensitivity: down to -137 dBm
      • Bullet-proof front end: IIP3 = -12.5 dBm
      • 89 dB blocking immunity
      • Low Rx current of 10 mA, 200 nA register retention
      • Fully integrated synthesizer with a resolution of 61 Hz
      • Built-in bit synchronizer for clock recovery
      • Sync word recognition
      • Preamble detection
      • 127 dB+ dynamic range RSSI
      • LoRaWAN™ Class A certified
    • SMA and U.FL RF interface connectors
    • Including 50-ohm SMA RF antenna
    • 7 LEDs:
      • 4 general-purpose LEDs
      • 5 V power LED
      • ST-LINK-communication LED
      • Fault-power LED
    • 1 user and 1 reset push-buttons
    • On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
    • Arduino™ Uno V3 connectors
    • Board power supply through the USB bus or external VIN/3.3 V supply voltage or batteries
    • 3 × AAA-type battery holder for standalone operation
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil®, GCC-based IDEs, Arm® Mbed™

You might also like...

The current status of a product:
Active: Product is in volume production
Evaluation: Product is under characterization. Limited Engineering samples available
Preview: Product is in design stage
Target: Product is in design feasibility stage.No commitment taken to produce
Proposal: Marketing proposal for customer feedback.No commitment taken to design or produce
NRND: Not Recommended for New Design.Product is in volume production only to support customers ongoing production.
The RoHS status of a product:
ECOPACK 1: Initial grade to identify European RoHS compliant products.
ECOPACK 2: New grade to identify brominated chlorinated and antimony oxide flame retardant free products.
ECOPACK 3: Halogen free RoHS exemptions free products.
(*): ECOPACK 2 version available upon request.
(**): Some versions still existing in ECOPACK 1 or not compliant.
The current status of a product:
Active: Product is in volume production
Evaluation: Product is under characterization. Limited Engineering samples available
Preview: Product is in design stage
Target: Product is in design feasibility stage.No commitment taken to produce
Proposal: Marketing proposal for customer feedback.No commitment taken to design or produce
NRND: Not Recommended for New Design.Product is in volume production only to support customers ongoing production.
Budgetary PriceMain country of assembly or fabrication of the product.ECCNs are five character alpha-numeric designations used on the Commerce Control List to identify dual-use items for export control purposes. ECCNs are five character alpha-numeric designations used on the Commerce Control List to identify dual-use items for export control purposes.