Published November 13, 2019 © GPL3+

25 kHz 4 Pin PWM Fan Control with Arduino Uno

Control the speed of your PWM fan easily. No need for other circuits.

IntermediateFull instructions provided106,828

25 kHz 4 Pin PWM Fan Control with Arduino Uno

Things used in this project

Hardware components

Axial Fan, 12 VDC

4-Wire Variant with CONTROL wire; tachometer only won't work

Arduino UNO

USB-A to Mini-USB Cable

Jumper wires (generic)

Software apps and online services

Arduino IDE

Story

I have been wondering about this project and how to control my 4 pin PWM fans. I had 5 laying around and thought mine as well give it a shot. The frequency values can be adjusted between 125 HZ -- 8 MHZ as well as a variable duty cycle. The circuit utilizes the mode 10 PWM phase-correct on timer 1 OCR1A (Pin 9) and ICR1 (Pin 10). Some debugging was needed to figure out this and I do own a handheld oscilloscope. It makes seeing the frequencies and duty cycles much easier and no guessing is involved. Here's the link: The Oscilloscope.

1 / 2 • The oscilloscope makes quick work when analyzing the pulses.

I do strongly advise you look up the datasheet for your fan as the control pin in my case was yellow (Which is normally referred as tach wire). Be sure to also find the acceptable frequency range (OR "CENTERING FREQUENCY") for your chosen fan. You may need to change the code frequency to adjust to your needs. Finally you will need a good power supply (Mine is a converted ATX PSU from an old PC).

NOTE: I have attempted using another timer and controlling 2 fans independently. It doesn't work. The reason for this is the resolution of the 2nd timer is lower (16 bit vs 8 bit). This means steps in frequency and duty adjustments are noisy and the waveforms are more and more deformed. This also is not as straightforward when entering values.

Code can be found below and here:

- https://github.com/T-622/25KHz-Arduino-Fan-PWM-Control

Clone with:

- https://github.com/T-622/25KHz-Arduino-Fan-PWM-Control.git

Code

The Code

const byte OC1A_PIN = 9;
const byte OC1B_PIN = 10;

const word PWM_FREQ_HZ = 25000; //Adjust this value to adjust the frequency (Frequency in HZ!) (Set currently to 25kHZ)
const word TCNT1_TOP = 16000000/(2*PWM_FREQ_HZ);

void setup() {
  
  pinMode(OC1A_PIN, OUTPUT);

  // Clear Timer1 control and count registers
  TCCR1A = 0;
  TCCR1B = 0;
  TCNT1  = 0;

  // Set Timer1 configuration
  // COM1A(1:0) = 0b10   (Output A clear rising/set falling)
  // COM1B(1:0) = 0b00   (Output B normal operation)
  // WGM(13:10) = 0b1010 (Phase correct PWM)
  // ICNC1      = 0b0    (Input capture noise canceler disabled)
  // ICES1      = 0b0    (Input capture edge select disabled)
  // CS(12:10)  = 0b001  (Input clock select = clock/1)
  
  TCCR1A |= (1 << COM1A1) | (1 << WGM11);
  TCCR1B |= (1 << WGM13) | (1 << CS10);
  ICR1 = TCNT1_TOP;
}

void loop() {

    setPwmDuty(0);
    delay(5000);
    setPwmDuty(25); //Change this value 0-100 to adjust duty cycle
    delay(5000);
//    setPwmDuty(50);
//    delay(20000);
//    setPwmDuty(75);
//    delay(20000);
//    setPwmDuty(100);
//    delay(20000);
}

void setPwmDuty(byte duty) {
  OCR1A = (word) (duty*TCNT1_TOP)/100;
}

Credits

tylerpeppy

2 projects • 42 followers

Love Arduino and IoT projects!

25 kHz 4 Pin PWM Fan Control with Arduino Uno

Things used in this project

Hardware components

Software apps and online services

Story

Schematics

pwm_fan_ctrl_6xm3Jti8le.png

Code

The Code

Credits

tylerpeppy

Comments

Embed the widget on your own site

25 kHz 4 Pin PWM Fan Control with Arduino Uno

25 kHz 4 Pin PWM Fan Control with Arduino Uno

Things used in this project

Hardware components

Software apps and online services

Story

Schematics

pwm_fan_ctrl_6xm3Jti8le.png

Code

The Code

Credits

tylerpeppy

Comments

Related channels and tags