Hackster is hosting Hackster Holidays, Ep. 6: Livestream & Giveaway Drawing. Watch previous episodes or stream live on Monday!Stream Hackster Holidays, Ep. 6 on Monday!
Rucksikaa Raajkumar
Published © CC BY

COVID-19 Remote Health monitoring system ( IoT )

A cost-effective and open source system to data log health measurements in Google sheets and allows the doctor to monitor them from anywhere

IntermediateFull instructions provided2.5 hours13,730
Early Bird - US Based Project
2021 China-US Young Maker Competition
COVID-19 Remote Health monitoring system ( IoT )

Things used in this project

Hardware components

NodeMCU ESP8266 Breakout Board
NodeMCU ESP8266 Breakout Board
×1
Solderless Breadboard Full Size
Solderless Breadboard Full Size
×1
Heartbeat sensor module
×1
Gravity: DS18B20 Temperature Sensor (Arduino Compatible)
DFRobot Gravity: DS18B20 Temperature Sensor (Arduino Compatible)
×1
Pushbutton switch 12mm
SparkFun Pushbutton switch 12mm
×2
IR tracking sensor module
×1
5 mm LED: Yellow
5 mm LED: Yellow
×1
Two-colour LED module
×1
Resistor 10k ohm
Resistor 10k ohm
×2
Male/Male Jumper Wires
×1

Software apps and online services

Arduino IDE
Arduino IDE
Pushingbox
Google Sheets
Google Sheets

Story

Read more

Schematics

Schematic

I could not get all the components in Fritzing, so I decided to draw the schematic by myself.

Hardware setup

Connections - NodeMCU ESP8266 Breakout board

Code

Threshold value

Arduino
GettingStartedProject.ino
/*  PulseSensor Starter Project and Signal Tester
 *  The Best Way to Get Started  With, or See the Raw Signal of, your PulseSensor.com™ & Arduino.
 *
 *  Here is a link to the tutorial
 *  https://pulsesensor.com/pages/code-and-guide
 *
 *  WATCH ME (Tutorial Video):
 *  https://www.youtube.com/watch?v=RbB8NSRa5X4
 *
 *
-------------------------------------------------------------
1) This shows a live human Heartbeat Pulse.
2) Live visualization in Arduino's Cool "Serial Plotter".
3) Blink an LED on each Heartbeat.
4) This is the direct Pulse Sensor's Signal.
5) A great first-step in troubleshooting your circuit and connections.
6) "Human-readable" code that is newbie friendly."

*/
//  Variables
int PulseSensorPurplePin = 0;        // Pulse Sensor PURPLE WIRE connected to ANALOG PIN 0
int LED13 = 13;   //  The on-board Arduion LED

int Signal;                // holds the incoming raw data. Signal value can range from 0-1024
int Threshold = 550;            // Determine which Signal to "count as a beat", and which to ingore.

// The SetUp Function:
void setup() {
  pinMode(LED13,OUTPUT);         // pin that will blink to your heartbeat!
   Serial.begin(9600);         // Set's up Serial Communication at certain speed.

}

// The Main Loop Function
void loop() {

  Signal = analogRead(PulseSensorPurplePin);  // Read the PulseSensor's value.
                                              // Assign this value to the "Signal" variable.

   Serial.println(Signal);                    // Send the Signal value to Serial Plotter.


   if(Signal > Threshold){                          // If the signal is above "550", then "turn-on" Arduino's on-Board LED.
     digitalWrite(LED13,HIGH);
   } else {
     digitalWrite(LED13,LOW);                //  Else, the sigal must be below "550", so "turn-off" this LED.
   }


delay(10);


}

Google script

JavaScript
//-----------------------------------------------
//Originally published by Mogsdad@Stackoverflow
//Modified for jarkomdityaz.appspot.com
//Modified for Hackster.io by Stephen Borsay
//Modified for Hackster.io COVID19DetectProtect challenge by Rucksikaa Raajkumar
//-----------------------------------------------
/*
GScript, PushingBox and Arduino/ESP8266 Variables in order:

hData
cData
fData
----------------------------------------------------
*/
/* Using spreadsheet API */

function doGet(e) { 
  Logger.log( JSON.stringify(e) );  // view parameters

  var result = 'Ok'; // assume success

  if (e.parameter == undefined) {
    result = 'No Parameters';
  }
  else {
    var id = 'Your spreadsheet URL key';//docs.google.com/spreadsheetURL/d
    var sheet = SpreadsheetApp.openById(id).getActiveSheet();
    var newRow = sheet.getLastRow() + 1;
    var rowData = [];
    //var waktu = new Date();
    rowData[0] = new Date(); // Timestamp in column A
    
    for (var param in e.parameter) {
      Logger.log('In for loop, param='+param);
      var value = stripQuotes(e.parameter[param]);
      //Logger.log(param + ':' + e.parameter[param]);
      switch (param) {
        case 'hData': //Parameter
          rowData[1] = value; //Value in column B
          break;
        case 'cData':
          rowData[2] = value;
          break;
        case 'fData':
          rowData[3] = value;
          break;
        default:
          result = "unsupported parameter";
      }
    }
    Logger.log(JSON.stringify(rowData));

    // Write new row below
    var newRange = sheet.getRange(newRow, 1, 1, rowData.length);
    newRange.setValues([rowData]);
  }

  // Return result of operation
  return ContentService.createTextOutput(result);
}

/**
* Remove leading and trailing single or double quotes
*/
function stripQuotes( value ) {
  return value.replace(/^["']|['"]$/g, "");
}

Credits

Rucksikaa Raajkumar

Rucksikaa Raajkumar

43 projects • 94 followers
Amateur Arduino Developer. Undergraduate. YouTuber (https://www.youtube.com/c/RucksikaaRaajkumar/videos) and Blogger (Arduino Projects by R)

Comments

Awards
Early Bird - US Based Project
2021 China-US Young Maker Competition
Related channels and tags
  • COVID-19
  • COVID-19
  • DFRobot
  • Espressif
  • Fitness
  • Fitness
  • Google
  • Health & Medical Devices
  • Health & Medical Devices
  • NodeMCU
  • Sensors
  • Sensors
  • SparkFun