NEW SINGLE SHOT ALGORITHM BASED CODE,FOR FASTER AND MUCH MORE CHANGE ADAPTIVE MEASUREMENTS :-

Published April 30, 2020 © GPL3+

Arduino based RPM counter with a new and faster algorithm

This project makes use of the preciseness of a laser beam, just one IR sensor and that good old arduino board to measure the RPM of motors.

BeginnerFull instructions provided36,038

Arduino based RPM counter with a new and faster algorithm

Things used in this project

Hardware components

Arduino UNO

IR proximity sensor

Use the sensor recommended in this project otherwise the results may vary

Jumper wires (generic)

Laser Diode, 655 nm

You can use a readymade laser pointer and not necessarily the above mentioned one.

DC motor (generic)

this is for testing.

USB-A to Mini-USB Cable

Battery, 9 V

Software apps and online services

Arduino IDE

Hand tools and fabrication machines

Solder Wire, Lead Free

Soldering iron (generic)

only for soldering wires to motor leads.you can use any other means also.

Story

FULL IMAGE OF THE PROJECT SETUP.

This project is developed from scratch as an attempt to measure the exact RPM (Rotations per Minute)value of various motors using a single IR sensor, an Arduino board and an essential key ingredient -a Laser Pointer(necessarily Red).

This project uses the fact that the IR sensor also reads the the low number of IR radiations given off by the red laser. However when a blue/green laser is used these IR radiations get very less and the analog read voltage drops down to approx. 0.

When a blade of the fan attached to the motor comes in the path of the laser beam it blocks up the pathway and the reading drops to 0. The fan blade keeps on spinning and its position keeps on changing with a constant supply of power. A constant change of path occurs. When the path becomes clear again, the laser pointer beam strikes the sensor again.

NEW SINGLE SHOT ALGORITHM BASED CODE,FOR FASTER AND MUCH MORE CHANGE ADAPTIVE MEASUREMENTS :-

The code for this project which is developed by me uses a newly developed algorithm for this project. The algorithm is indeed unique and is built to make measurements in less than 40 milliseconds and deliver accurate results. One very important feature of this program is that it uses a method which I call Single Shot Detection for Arduino. It calculates the RPM of the motor every time the fan blade creates an obstruction in the path of the laser beam. This is because the obstruction of the path of the laser beam marks a 1/n complete revolution for n number of blades in the fan. So, the program is very sensitive to even minute changes in the RPM ( upto 2 places of decimal) in every 1/n th revolution of the fan blade again where n is the number of blades of the fan. Hence this unique Single Shot Detection algorithm provides extremely accurate value of RPM and higher sensitivity to changes in measurements.

THE OUTPUT FOR A DC MOTOR(OPERATING AT 5 V).

In the above displayed image of an output sample from the serial monitor in a test run, the rate of output screening can clearly be seen which is about 2 times a second. The RPM values are calculated upto two places of decimals each time.

Everyone viewing this must try this project once and share your valuable reviews. Do tell about your experiments and their outcomes related to this algorithm. Suggestions for new projects are welcomed in the comments section. If you like the project, do respect it.

Follow my profile by tapping on this link(https://create.arduino.cc/projecthub/YASH36) @YASH36 for some new project updates.

Until then, Stay Safe and enjoy Arduino!!

Code

RPM_counter_101

//code by YaSh.

int sen = A0;
const float wid = 0.012;   //adjust the width of the fan blade according to your needs.
const float rad = 0.045;   //adjust the radius of the point of detection in the fan blade.
const float konst = 6.2832;  //  2*pi.
float time_1;
float time_2;
float vel;
float diff;
float tnet;
float rpm;
void setup() 
{
  Serial.begin(9600);
  pinMode(sen,INPUT);
  Serial.print(" \n please start the motor at least 3 seconds prior.\n");
  delay(3000);
}
void loop()
{
  if(analogRead(sen)<950)
  {
    time_1 = millis();
    delay(30);
  }
  if(analogRead(sen)>950)
  {
    time_2 = millis();
    diff = (time_2-time_1);         
    vel = wid/diff;                      //rotation velocity
    tnet = (konst*rad)/vel;              //time = (2*pi*radius)/velocity.
    rpm = (60000)/tnet;                // time in ms to minutes and then to rpm conversion step.
  }
Serial.print("\n The rpm is : "); 
Serial.println( rpm );
}

Credits

yashastronomy

0 projects • 16 followers

Arduino based RPM counter with a new and faster algorithm

Things used in this project

Hardware components

Software apps and online services

Hand tools and fabrication machines

Story

NEW SINGLE SHOT ALGORITHM BASED CODE,FOR FASTER AND MUCH MORE CHANGE ADAPTIVE MEASUREMENTS :-

Schematics

Setup image.

Circuit Schematics

Code

RPM_counter_101

Credits

yashastronomy

Comments

Embed the widget on your own site

Arduino based RPM counter with a new and faster algorithm

Arduino based RPM counter with a new and faster algorithm

Things used in this project

Hardware components

Software apps and online services

Hand tools and fabrication machines

Story

NEW SINGLE SHOT ALGORITHM BASED CODE,FOR FASTER AND MUCH MORE CHANGE ADAPTIVE MEASUREMENTS :-

Schematics

Setup image.

Circuit Schematics

Code

RPM_counter_101

Credits

yashastronomy

Comments

Related channels and tags